Most firms that put a confidentiality or disclaimer line on their letters type it in the wrong place. It sits at the bottom of the letter body, below the signature block, and it moves every time someone adds a paragraph. The fix is structural. The line belongs in the Word footer, formatted once, locked, and saved in a template.
This guide covers the law firm letter footer disclaimer format word users need: font size, alignment, spacing, first-page versus continuation-page behavior, and locking. It covers layout only. What the line says, and whether your firm needs one, is a question for your own counsel. Nothing here suggests any particular wording is enough.
Why a disclaimer typed into the letter body drifts
Text in the body flows with the letter. A short letter leaves the disclaimer floating halfway down the page. A long letter pushes it to page 2, sometimes split across the page break. Someone deletes a blank line and the disclaimer moves up against the signature. Someone pastes from an old letter and brings in a different font size.
The footer works differently. Word draws footer content in a fixed zone at the bottom of every page, separate from the body. It does not reflow when the letter gets longer or shorter. Type the line there once and it shows up in the same spot on every letter made from the template.
There is a second benefit. A body-text disclaimer gets copied, edited, and "cleaned up" by whoever drafts the letter. A footer disclaimer is out of the way, and with the right settings it can't be touched without deliberate effort.
Footer format specs: size, alignment, spacing, and margins
These specs are a practical starting point for a law firm letter footer disclaimer format in Word on a US Letter page. Adjust to match your letterhead design, but set every value on purpose rather than accepting Word's defaults.
- Font and size: Use the same typeface as your letterhead's address line, or the body font. 7 to 8 pt is the usual range for a small-print footer line. Below 7 pt, many office printers start to blur serifs.
- Alignment: Match the letterhead. If the address line is centered, center the disclaimer. If the design is left-aligned to the body margin, left-align the disclaimer to the same margin so the edges line up.
- Line spacing: Set it to Exactly, not Single. For 7.5 pt text, Exactly 9 pt keeps lines tight and predictable. "Single" lets Word pick a height based on the font, which changes if someone swaps fonts.
- Paragraph spacing: 0 pt before, 0 pt after. Control gaps with a deliberate value, not stray empty paragraphs.
- Footer distance from edge: Layout > Margins > Custom Margins > Layout tab > From edge: Footer. 0.4 to 0.5 in is a safe range. Many office printers can't print within about 0.25 in of the paper edge.
- Bottom margin: Must be larger than the footer distance plus the full height of the footer content. If it isn't, Word quietly pushes the body up and your page layout shifts.
Do this through the built-in Footer style, not by formatting the text directly. Modify the Footer style (Home > Styles > right-click Footer > Modify) with the font, size, and spacing above. Then any footer paragraph picks up the right format automatically. Our guide on Word page margins for letterhead covers the margin math in more detail.
Page 1 versus continuation pages: setting the footer per page
Many firm letterheads use a full design on page 1 and a stripped-down version on page 2 onward. Word handles this with one checkbox: double-click the footer, then tick Different First Page on the Header & Footer tab.
That gives you two separate footers:
- First Page Footer. Usually holds the office address line plus the disclaimer.
- Footer (used for page 2 and after). Usually holds a smaller version: the disclaimer alone, or the disclaimer plus a page number.
The common mistake is setting up the first-page footer, ticking the checkbox, and forgetting the continuation footer is a separate, empty footer. Open page 2 of a test letter and check it. If the disclaimer should appear there too, type it into that footer as well. Whether it appears on every page is your firm's call. Word just needs to be told.
Keep the disclaimer in the same position on both footers if you can. A line that sits 0.45 in from the edge on page 1 and 0.6 in on page 2 looks like a mistake. For the header side of the same setup, see Word letterhead second page different header.
Keep the disclaimer from colliding with the address line or page edge
When the address line and the disclaimer share a footer, they compete for space. Three rules keep them apart.
Stack them as inline paragraphs, not text boxes. A floating text box can drift when the page size changes or a document opens on a different machine. Two plain paragraphs in the footer stay in order.
Give the gap a fixed value. Put 4 to 6 pt of space before the disclaimer paragraph, set in paragraph settings. Do not use an empty line. An empty line takes its height from the font, and that changes.
Check the total height. Add it up: address line (say 9 pt line) + gap (5 pt) + disclaimer (two lines at 9 pt). That comes to about 32 pt, or roughly 0.45 in. With a 0.45 in footer distance, the footer content reaches about 0.9 in from the bottom edge. Your bottom margin needs to be at least that, plus a little air, so 1 in works. If the disclaimer wraps to three lines, recheck the math.
If your design has footer artwork, like a rule or a colored band, keep the text paragraphs clear of it. The letterhead footer guide walks through locking the address line itself.
Lock the footer so staff can't edit it by accident
A footer is less exposed than body text, but anyone can double-click into it. Two methods stop accidental edits.
Content control lock. Turn on the Developer tab (File > Options > Customize Ribbon). Select the disclaimer text in the footer, insert a Rich Text Content Control around it, open Properties, and tick both Content control cannot be deleted and Contents cannot be edited. The text stays visible and prints normally, but typing into it does nothing.
Restrict Editing with body exceptions. On the Review tab, open Restrict Editing, choose No changes (Read only), then select the letter body area and tick Everyone as an exception. Headers and footers can't be made exceptions, so they stay locked while the body stays editable. Start enforcement with or without a password.
Then save the file as a .dotx template, not a .docx. Every new letter opens as a fresh copy and the master stays untouched. The dotx letterhead template article explains why the file type matters, and Lock Your Law Firm Letterhead Word Template covers locking styles across the whole document.
Getting the footer into a .dotx from your existing PDF letterhead
If your firm's letterhead exists as a designed PDF, you don't need to rebuild the footer artwork by hand. Letterhead Lab converts the PDF into an editable Word template. The header artwork goes into the Word header, the footer artwork goes into the Word footer, and the body stays clean for typing. The conversion runs in your browser, so the PDF never leaves your computer.
Once you have the template, apply the steps above. Set the Footer style, check Different First Page, add or confirm the disclaimer on each footer, check the height math, and lock it. If the disclaimer wording might change, keep it as live text in the footer rather than part of the artwork. That way an update is a text edit, not a new conversion.
Pricing is fixed. A single-page template is $19 at launch pricing (normally $39). A design with several page variants can go in the multi-page bundle, $49 at launch pricing (normally $79) for up to 10 pages from one PDF. For a two-page design (first page plus continuation), two single pages at $19 each comes to $38, so the bundle makes sense from three pages up. Preview is free, and you pay only when you download. Full details are on the pricing page, and you can see a finished layout on the law firm letterhead template page.
Set the footer once, lock it, and the disclaimer lands in the same place on every letter, whoever writes it. That is the whole point of a fixed law firm letter footer disclaimer format word template.